UGC NET 2018: July, Paper II, Electronic Science
Text of page 1
Signature and Name of Invigilator
1. (Signature) OMR Sheet No. : ..........................................................
(To be filled by the Candidate)
(Name)
Roll No.
2. (Signature)
(In figures as per admission card)
(Name)
Roll No.
J 0 8 8 1 8 PAPER - II (In words)
Time : 2 hours] ELECTRONIC SCIENCE [Maximum Marks : 200
Number of Pages in this Booklet : 32 Number of Questions in this Booklet : 100
Instructions for the Candidates ¬⁄UˡÊÊÁÕ¸ÿÙ¢ ∑§ Á‹∞ ÁŸŒ¸‡Ê
1. Write your roll number in the space provided on the top of
1. ß‚ ¬ÎDU ∑§ ™§¬⁄U ÁŸÿà SÕÊŸ ¬⁄U •¬ŸÊ ⁄UÙ‹U Ÿê’⁄U Á‹Áπ∞–
this page.
2. This paper consists of hundred multiple-choice type of 2. ß‚ ¬˝‡Ÿ-¬òÊ ◊¢ ‚ÊÒ ’„ÈÁfl∑§À¬Ëÿ ¬˝‡Ÿ „Ò¥–
questions. 3. ¬⁄UˡÊÊ ¬˝Ê⁄êU÷ „ÙŸ ¬⁄U, ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê •Ê¬∑§Ù Œ ŒË ¡ÊÿªË– ¬„‹U ¬UÊ°ø Á◊Ÿ≈U
3. At the commencement of examination, the question booklet •Ê¬∑§Ù ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê πÙ‹Ÿ ÃÕÊ ©‚∑§Ë ÁŸêŸÁ‹Áπà ¡Ê°ø ∑§ Á‹∞ ÁŒÿ
will be given to you. In the first 5 minutes, you are requested ¡Êÿ¢ª, Á¡‚∑§Ë ¡Ê°ø •Ê¬∑§Ù •fl‡ÿ ∑§⁄UŸË „Ò —
to open the booklet and compulsorily examine it as below :
(i) ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê πÙ‹Ÿ ∑§ Á‹∞ ¬ÈÁSÃ∑§Ê ¬⁄U ‹ªË ∑§Êª¡ ∑§Ë ‚Ë‹ ∑§Ê
(i) To have access to the Question Booklet, tear off the
paper seal on the edge of this cover page. Do not accept »§Ê«∏ ‹¢U– πÈ‹Ë „È߸ ÿÊ Á’ŸÊ S≈UË∑§⁄U-‚Ë‹U ∑§Ë ¬ÈÁSÃ∑§Ê SflË∑§Ê⁄U Ÿ ∑§⁄¢U–
a booklet without sticker-seal and do not accept an open (ii) ∑§fl⁄U ¬ÎDU ¬⁄U ¿U¬ ÁŸŒ¸‡ÊÊŸÈ‚Ê⁄U ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê ∑§ ¬ÎDU ÃÕÊ ¬˝‡ŸÙ¢ ∑§Ë
booklet. ‚¢ÅÿÊ ∑§Ù •ë¿UË Ã⁄U„ øÒ∑§ ∑§⁄U ‹¢U Á∑§ ÿ ¬Í⁄U „Ò¢U– ŒÙ·¬Íáʸ ¬ÈÁSÃ∑§Ê
(ii) Tally the number of pages and number of questions in Á¡Ÿ◊¢ ¬ÎDU/¬˝‡Ÿ ∑§◊ „Ù¢ ÿÊ ŒÈ’Ê⁄UÊ •Ê ªÿ „Ù¢ ÿÊ ‚ËÁ⁄Uÿ‹U ◊¢ Ÿ „Ù¢
the booklet with the information printed on the cover •ÕʸØ Á∑§‚Ë ÷Ë ¬˝∑§Ê⁄U ∑§Ë òÊÈÁ≈U¬Íáʸ ¬ÈÁSÃ∑§Ê SflË∑§Ê⁄U Ÿ ∑§⁄¢U ÃÕÊ
page. Faulty booklets due to pages/questions missing
or duplicate or not in serial order or any other ©‚Ë ‚◊ÿ ©‚ ‹Uı≈UÊ∑§⁄U ©‚∑§ SÕÊŸ ¬⁄U ŒÍ‚⁄UË ‚„Ë ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê ‹
discrepancy should be got replaced immediately by a ‹¢– U ß‚∑§ Á‹∞ •Ê¬∑§Ù ¬Ê°ø Á◊Ÿ≈U ÁŒÿ ¡Êÿ¢ª– ©‚∑§ ’ÊŒ Ÿ ÃÙ
correct booklet from the invigilator within the period •Ê¬∑§Ë ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê flʬ‚ ‹Ë ¡ÊÿªË •ı⁄U Ÿ „Ë •Ê¬∑§Ù •ÁÃÁ⁄UQ§
of 5 minutes. Afterwards, neither the Question Booklet ‚◊ÿ ÁŒÿÊ ¡ÊÿªÊ–
will be replaced nor any extra time will be given.
(iii) ß‚ ¡Ê°ø ∑§ ’ÊŒ ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê ∑§Ê Ÿ¥’⁄U OMR ¬òÊ∑§ ¬⁄U •¢Á∑§Ã ∑§⁄¢U
(iii) After this verification is over, the Test Booklet Number
should be entered on the OMR Sheet and the OMR Sheet
•Uı⁄U OMR ¬òÊ∑§ ∑§Ê Ÿ¥’⁄U ß‚ ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê ¬⁄U •¢Á∑§Ã ∑§⁄U Œ¢–
Number should be entered on this Test Booklet. 4. ¬˝ àÿ∑§ ¬˝‡Ÿ ∑§ Á‹∞ øÊ⁄U ©ûÊ⁄U Áfl∑§À¬ (1), (2), (3) ÃÕÊ (4) ÁŒÿ ªÿ „Ò¢–
4. Each item has four alternative responses marked (1), (2), (3) •Ê¬∑§Ù ‚„Ë ©ûÊ⁄U ∑§ flÎûÊ ∑§Ù ¬Ÿ ‚ ÷⁄U∑§⁄U ∑§Ê‹Ê ∑§⁄UŸÊ „Ò ¡Ò‚Ê Á∑§ ŸËø
and (4). You have to darken the circle as indicated below on ÁŒπÊÿÊ ªÿÊ „Ò–
the correct response against each item.
©ŒÊ„⁄UáÊ — ¡’Á∑§ (3) ‚„Ë ©ûÊ⁄U „Ò–
Example : where (3) is the correct response.
5. ¬˝‡ŸÊ¥ ∑§ ©ûÊ⁄U ∑§fl‹ ¬˝‡Ÿ ¬ÈÁSÃ∑§Ê ∑§ •ãŒ⁄U ÁŒÿ ªÿ OMRU ¬òÊ∑§ ¬⁄U „Ë
5. Your responses to the items are to be indicated in the OMR
•¥Á∑§Ã ∑§⁄UŸ „Ò¥– ÿÁŒ •Ê¬ OMRU ¬òÊ∑§ ¬⁄U ÁŒÿ ªÿ flÎûÊ ∑§ •‹ÊflÊ Á∑§‚Ë
Sheet given inside the Booklet only. If you mark your
response at any place other than in the circle in the OMR •ãÿ SÕÊŸ ¬⁄U ©ûÊ⁄U ÁøqÊ¢Á∑§Ã ∑§⁄Uà „Ò¥, ÃÙ ©‚∑§Ê ◊ÍÀUÿÊ¢∑§Ÿ Ÿ„Ë¢ „٪ʖ
Sheet, it will not be evaluated. 6. •ãŒ⁄U ÁŒÿ ªÿ ÁŸŒ¸‡ÊÙ¢ ∑§Ù äÿÊŸ¬Ífl¸∑§ ¬…∏¢U–
6. Read instructions given inside carefully. 7. ∑§ìÊÊ ∑§Ê◊ (Rough Work) ß‚ ¬ÈÁSÃ∑§Ê ∑§ •ÁãÃ◊ ¬ÎDU ¬⁄U ∑§⁄¢U–
7. Rough Work is to be done in the end of this booklet.
8. ÿÁŒ •Ê¬ OMR ¬òÊ∑§ ¬⁄U ÁŸÿà SÕÊŸ ∑§ •‹ÊflÊ •¬ŸÊ ŸÊ◊, ⁄UÊ‹ Ÿê’⁄U,
8. If you write your Name, Roll Number, Phone Number or
put any mark on any part of the OMR Sheet, except for the
»§ÊŸ Ÿê’⁄U ÿÊ ∑§Ê߸ ÷Ë ∞‚Ê Áøq Á¡‚‚ •Ê¬∑§Ë ¬„øÊŸ „Ê ‚∑§, •¥Á∑§Ã ∑§⁄UÃ
space allotted for the relevant entries, which may disclose „Ò¥ •ÕflÊ •÷Œ˝ ÷Ê·Ê ∑§Ê ¬˝ÿʪ ∑§⁄Uà „Ò¥, ÿÊ ∑§Ê߸ •ãÿ •ŸÈÁøà ‚ÊœŸ ∑§Ê
your identity, or use abusive language or employ any other ¬˝ÿʪ ∑§⁄Uà „Ò¥, ¡Ò‚ Á∑§ •¥Á∑§Ã Á∑§ÿ ªÿ ©ûÊ⁄U ∑§Ê Á◊≈UÊŸÊ ÿÊ ‚»§Œ SÿÊ„Ë ‚
unfair means, such as change of response by scratching or ’Œ‹ŸÊ ÃÊ ¬⁄UˡÊÊ ∑§ Á‹ÿ •ÿÊÇÿ ÉÊÊÁ·Ã Á∑§ÿ ¡Ê ‚∑§Ã „Ò¥–
using white fluid, you will render yourself liable to 9. •Ê¬∑§Ù ¬⁄UˡÊÊ ‚◊Ê# „ÙŸ §¬⁄U ◊Í‹ OMR ¬òÊ∑§ ÁŸ⁄UˡÊ∑§ ◊„ÙŒÿ ∑§Ù ‹Uı≈UÊŸÊ
disqualification. •Êfl‡ÿ∑§ „Ò •ı⁄U ¬⁄UˡÊÊ ‚◊ÊÁ# ∑§ ’ÊŒ ©‚ •¬Ÿ ‚ÊÕ ¬⁄UˡÊÊ ÷flŸ ‚ ’Ê„⁄U
9. You have to return the original OMR Sheet to the invigilators Ÿ ‹∑§⁄U ¡Êÿ¢– „Ê‹Ê¥Á∑§ •Ê¬ ¬⁄UˡÊÊ ‚◊ÊÁ# ¬⁄U ◊Í‹ ¬˝‡Ÿ-¬ÈÁSÃ∑§Ê •¬Ÿ ‚ÊÕ
at the end of the examination compulsorily and must not
carry it with you outside the Examination Hall. You are ‹ ¡Ê ‚∑§Ã „Ò¥–
however, allowed to carry original question booklet on 10. ∑§fl‹ ŸË‹/∑§Ê‹ ’Ê‹U åflÊßZ≈U ¬Ÿ ∑§Ê „Ë ¬˝ÿʪ ∑§⁄¢U–
conclusion of examination.
11. Á∑§‚Ë ÷Ë ¬˝∑§Ê⁄U ∑§Ê ‚¢ªáÊ∑§ (∑Ò§‹∑ȧ‹≈U⁄U) UÿÊ ‹Êª ≈U’‹ •ÊÁŒ ∑§Ê
10. Use only Blue/Black Ball point pen.
¬˝ÿÙª flÁ¡¸Ã „Ò–
11. Use of any calculator or log table etc., is prohibited.
12. ª‹Ã ©ûÊ⁄UÊ¥ ∑§ Á‹∞ ∑§Ê߸ Ÿ∑§Ê⁄UÊà◊∑§ •¥∑§ Ÿ„Ë¥ „Ò¥–
12. There are no negative marks for incorrect answers.
J-08818 !J-08818-PAPER-II! 1 P.T.O.
Text of page 2
ELECTRONIC SCIENCE
PAPER - II
Note : This paper contains hundred (100) objective type questions of two (2) marks each. All
questions are compulsory.
1. The simple one dimensional diffusion process can be given by :
∂ c (x ,t) ∂c ∂ 2 c ( x , t) ∂2c
(1) =D (x , t) (2) =D (x , t)
∂t ∂x ∂ t2 ∂ x2
∂ c (x , t) ∂2c ∂ 2 c (x , t) ∂c
(3) =D (x , t) (4) 2
=D (x , t)
∂t ∂x 2 ∂t ∂x
2. In an intrinsic semiconductor, the intrinsic carrier density is :
−Eg −Eg −Eg +Eg
(1) NcNv e 2 kT (2) Nc Nv e kT (3) NcNv e 2 kT (4) NcNv e kT
1
3. The frequency at which the transfer function H ( ω) of the following RC network is , will
2
be :
(1) 50 Hz (2) 200 Hz (3) 1900 Hz (4) 1378 Hz
5s +3
4. The Laplace transform of a signal f(t) is given as ; F (s) = . The signal will be :
s (s +1)
(1) 2u(t)+3e−t (2) 3u(t)−2e−t (3) 3u(t)+2e−t (4) 2u(t)−3e−t
J-08818 !J-08818-PAPER-II! 2 Paper-II
Text of page 3
5. In a circuit shown below, the base current IB is :
(1) 18.58 µA (2) 19.73 µA (3) 60.10 µA (4) 2.63 µA
6. The unity follower circuit is :
(1) (2)
(3) (4)
J-08818 !J-08818-PAPER-II! 3 Paper-II
Text of page 4
7. The advantage/disadvantage of Schottky TTL logic circuit over Standard TTL logic circuit is
that :
(1) It provides low power consumption
(2) It virtually eliminates saturation delay time
(3) It provides simple circuitary
(4) It gives low switching speed
8.
In a J-K flip-flop we have J=Q and K=1 (shown in figure). Assuming the flip-flop was
initially cleared and clocked for 6 pulses, the sequence at the Q output will be :
(1) 010000 (2) 011001 (3) 010010 (4) 010101
9. In which of the following number systems, AC flag is used in 8085 µp ?
(1) Octal (2) BCD (3) Binary (4) Hexadecimal
10. JMP 2034H in 8085 µp is an example of __________.
(1) 1 byte instruction (2) 2 byte instruction
(3) 3 byte instruction (4) None of the above
11. Which of the following is the correct output for the ‘C’ program given below :
#include<stdio.h>
void afun(char *) ;
int main( )
{
char ch[10] ;
ch[0]=‘X’ ; ch[1]=’Y’ ; ch[2]=‘Z’ ;
ch[3]=‘W’ ;
afun (& ch[0]) ;
return 0 ;
}
void afun (char *c)
{
c++ ;
printf(“%c”, *c) ;
c++ ;
printf(“%c\n”, *c) ;
}
Correct output is :
(1) XY (2) YZ
(3) ZW (4) None of the above
J-08818 !J-08818-PAPER-II! 4 Paper-II
Text of page 5
12. Consider the following expression in ‘C’
8+9/3*3−4+9%6 ;
which evaluates to :
(1) 10 (2) 8 (3) 14 (4) 16
13. Which of the following statements in FORTRAN is non-executable statement ?
(1) DO (2) FORMAT (3) IF (4) READ
14. A TRAPATT diode has the following parameters :
Doping concentration=2×1015 cm−3
Current density=20 KA/cm2
The avalanche zone velocity of carriers is given by :
(1) 2.25×105 m/s (2) 6.25×107 cm/s
(3) 6.25×103 m/s (4) 2.35×108 m/s
15. The Loading is sometimes used with an antenna in order to increase the :
(1) Bandwidth (2) Beam width
(3) Effective height (4) Input capacitance
16. Thermal noise is passed through an ideal low-pass filter having cut-off at fc=ω Hz. The
auto-correlation value of the noise at the output of the filter is given as :
(1) A delta function at t=0
(2) Gaussian over the range−∞ ≤ t ≤ ∞
(3) Sinc function over the range −∞ ≤ t ≤ ∞
1 1
(4) Triangular function over the range − ω ≤ t ≤ ω
2 2
17. Which of the following statement is correct ?
(1) MF radio frequency waves are called long waves and HF are called short waves.
(2) VLF and LF radio frequency waves are called long waves while HF waves are called
short waves.
(3) ELF radio waves are called long waves and HF are called short waves.
(4) LF radio waves are called long waves and VHF are called short waves.
18. A single mode fiber with radius of 4.2 µm, with core-refractive index =1.48 and that of
cladding=1.475, the cut-off wavelength is given by :
(1) λc =1334 nm (2) λc =1525 nm (3) λc =990 nm (4) λc =1290 nm
J-08818 !J-08818-PAPER-II! 5 Paper-II
Text of page 6
19. A thermostatic cut-out works on the principle of :
(1) Thermal expansion of fluids
(2) Expansion due to air pressure
(3) Variation of resistance with temperature
(4) Thermal expansion of metals
20. If h is the Hydrogen ion concentration in gm/l, the pH value is given as :
1
(1) log h (2) −log h (3) log (1+h) (4) log
(1 + h )
21. In a JFET, the maximum value of transconductance gm is :
I DSS 2I D S S 2 I DSS I DSS
(1) VP (2) VP (3) VP (4) VP
22. The cut-off frequency of TEM wave is :
(1) Zero (2) 11.0 GHz (3) ∞ (4) Moderate
23. Limiter circuit is not needed in the following detector :
(1) Foster - Seeley discriminator (2) Balanced slope
(3) Ratio detector (4) None
24. Which of the following is used to analyze all kind of matters ?
(1) Spectrophotometers (2) Electron Microscope
(3) X-ray diffractometer (4) Spectrum analyzer
25. In a Silicon oxidation model, if hG is the gas phase mass transfer co-efficient, CG is the oxidant
concentration in the bulk of the gas and CS is the oxidant concentration adjacent to the oxide
surface, then for steady state, the gas phase flux can be expressed as :
(C S−CG ) (C G−C S )
(a) hG (b) hG (c) hG (CG−CS) (d) hG (CS−CG)
of these statements.
(1) (a) and (c) are correct
(2) (b) is correct but (d) is wrong
(3) (c) is correct but (a) is wrong
(4) (a), (b) and (c) are correct but (d) is wrong
J-08818 !J-08818-PAPER-II! 6 Paper-II
Text of page 7
26. When acceptor impurities of concentration NA are added to a semiconductor crystal, when
n is the electron density in the conduction band and p is the hole density in the valence band,
the ionised acceptors are given as :
NA
NA
E −EF
(a) E −EF (b) 1−4 exp A
1+4 exp A kT
kT
NA NA
E −E E −E
(c) 1+4 exp D F (d) 1−2 exp D F
kT kT
of these statements :
(1) (a) and (b) are wrong
(2) (a) is correct but (c) is wrong
(3) (c) is correct but (d) is wrong
(4) (d) is correct but (c) is wrong
27. Which of the following statements are correct for the A/D converters :
(a) The advantage of using a dual slope A/D converter in a digital voltmeter is that its
accuracy is high.
(b) The number of comparators in a 4-bit flash A/D converters is 15.
(c) The minimum number of comparators required to built an 8-bit flash A/D converter
is 256.
(d) The number of comparators required in a 3-bit comparator type A/D converters is 8.
Options :
(1) (a), (c) and (d) are correct
(2) (b) and (c) are correct
(3) (a) and (b) are correct
(4) (a), (b), (c) and (d) are correct
28. Which of the following statements are correct ?
(a) CMOS has higher speed and smaller power than BJT.
(b) CMOS ICs inputs should never be left unconnected as it may damage the device.
(c) CMOS ICs with Schmitt trigger inputs are useful for better noise immunity.
(d) CMOS is most popular logic family in VLSI Technology.
Options :
(1) (a), (c) and (d) are correct
(2) (b), (c) and (d) are correct
(3) (a), (b) and (c) are correct
(4) (a), (b) and (d) are correct
J-08818 !J-08818-PAPER-II! 7 Paper-II
Text of page 8
29. Which of the following statements are correct in respect to 8086 µp ?
(a) The instruction queue size is 8 bytes
(b) Segment register size is 16 bit while physical address size is 20 bits
(c) Segments are disjoint
(d) Beginning address of a segment must be divisible by (16)10
The correct answer is :
(1) (a) and (b) are correct
(2) (b) and (d) are correct
(3) (b) and (c) are correct
(4) (a) and (c) are correct
30. What happens when RET statement is executed in 8085 µp ?
(a) Program counter is cleared
(b) Control is transferred from the subroutine to the main program
(c) Returning address is loaded into the accumulator
(d) Returning address is loaded into the program counter from the top of the stack
The correct answer is :
(1) (a) and (c) (2) (b) and (d) (3) (a) and (b) (4) (b) and (c)
31. If ‘a’ is declared as one-dimensional array in ‘C’ then
(a) *(a+i) is same as *( &a[i] )
(b) *(a+i) is same as *a+i
(c) &a[i] is same as a+i−1
(d) *(a+i) is same as a[i]
Which of the above statements are incorrect ?
(1) (a) and (b) (2) (a) and (d) (3) (b) and (c) (4) (c) and (d)
32. Which of the following specifiers in C++ need not be honored by the compiler ?
(a) static (b) inline (c) extern (d) register
Which of the following is correct ?
(1) (b) and (d) (2) (a) and (b)
(3) (c) and (d) (4) (a) and (d)
J-08818 !J-08818-PAPER-II! 8 Paper-II
Text of page 9
33. Which of the following statements are true in case of Pulse Code Modulation (PCM) ?
S
(a) If the number of bits per sample is increased from n to n+1 ; the ratio would be
Nq
6 dB
(b) The quantization noise depends on sampling rate
(c) The main advantage of PCM is that it possesses better performance in presence of noise
(d) If the number of quantization levels increases from 4 to 64, the bandwidth increase by
a factor of 4
Options :
(1) (a) and (b) are correct (2) (a) and (c) are correct
(3) (a) and (d) are correct (4) (b) and (c) are correct
34. The following statements are correct for DSB-SC signal :
(a) It is a low pass filter
(b) It needs minimum transmitted power
(c) It is a result of product modulator
(d) Bandwidth of DSB-SC is twice the maximum frequency
Options :
(1) (a), (b) and (c) are correct (2) (b) and (d) are correct
(3) (a), (b) and (d) are correct (4) (a), (c) and (d) are correct
35. In an abrupt p-n junction if NA<< ND, then the barrier potential is :
q ND q NA 2 q ND 2 q (NA )
(a) W (b) W (c) W (d) W
2 ȏs 2 s 2 s 2 ȏs
of these statements :
(1) (a) is correct but (c) is wrong
(2) (b) is correct but (d) is wrong
(3) (c) is correct but (a) is wrong
(4) (d) is correct but (b) is wrong
36. In a voltage series feedback amplifier with load RL, if Ri is the input resistance without feedback,
then the input resistance with feedback is :
Ri R i βA v
(a) Ri (1+βAv) (b) Ri (1−βAv) (c) 1+βA v (d) RL
of these statements :
(1) (a) and (c) are correct (2) (b) and (d) are wrong
(3) (a) and (d) are wrong (4) (c) and (a) are wrong
J-08818 !J-08818-PAPER-II! 9 Paper-II
Text of page 10
37. Magnetron is a :
(a) O - type tube
(b) a low power device
(c) a high power device
(d) an oscillator
Out of the above following is correct option :
(1) (a) and (b) (2) (b) and (d) (3) (c) and (d) (4) (a), (c) and (d)
38. A Travelling Wave Tube Amplifier (TWTA) has the following properties :
(a) It provides an octave Bandwidth
(b) It provides an approximate gain of 40dB and more
(c) It has a low noise figure
(d) It has a very high noise figure
Out of the above statements following is correct :
(1) (a), (b) and (d) only
(2) (a) and (d) only
(3) (a) and (b) only
(4) (a) and (b) and (c) only
39. The block diagram of a feedback compensated system is given below :
Which of the following statements are correct ?
(a) When Kt=0, the feedback compensation is in-effective and the system is uncompensated
(b) When Kt=0, the feedback compensation is most effective and system is compensated
(c) The performance of the compensated system depends on Kt and T
(d) The performance of the compensated system does not depend on T
Options :
(1) (a) and (c) (2) (b) and (c) (3) (a) and (d) (4) (b) and (d)
J-08818 !J-08818-PAPER-II! 10 Paper-II
Text of page 11
40. The capacitor microphone is most widely used for precision measurements because it has :
(a) Good frequency response
(b) Excellent linearity
(c) Large dynamic pressure range
Which of the above are correct ?
(1) (a) and (b) only (2) (a) and (c) only (3) (b) and (c) only (4) (a), (b) and (c)
41. A good silicon APD has a capacitance of 5pF, with negligible dark current and is operating
with a post detection bandwidth of 50 MHz. The photocurrent before gain is given by
10−7 Amp. The operating temperature is 188C . The value of Load resistor to be connected
with APD is given by :
(1) 536.5 ohm (2) 635.5 ohm (3) 835.5 ohm (4) 83.5 ohm
42. For optical sources, following statements are given :
(a) They should have large spectral bandwidth
(b) They should have very narrow spectral line width
(c) They should accurately track the electrical input signal
(d) The source should have linearity property
Out of the above, following are correct :
(1) (a), (b), (c) only (2) (b), (c) and (d) only
(3) (b) and (c) only (4) (a), (c) and (d) only
43. A multimode graded index fiber, exhibits total pulse broadening of 0.1 µs over a distance of
15 km. Following data is estimated by using the concept of that there is no inter-symbol
interference :
(a) The maximum possible Bandwidth is 5 MHz
(b) The dispersion per unit length is 6.67 ns/km
(c) The maximum possible B.W. is 10 MHz
(d) The dispersion/unit length is 3.37 ns/km
Which is the correct option ?
(1) (a) and (d) (2) (b) and (c) (3) (c) and (d) (4) (a) and (b)
44. Consider the following statements regarding z-transform :
(a) The z-transform replaces the Laplace transform for sampled-data system
(b) The z-transform replaces the Laplace transform for continuous-data system
(c) The z-transform provides direct parallels to the s-plane analysis of transients, steady
state errors, stability etc.
(d) We cannot map points on s-plane to points on z-plane
Which of the above statements are correct ?
(1) (a) and (c) only (2) (a) and (d) only
(3) (b), (c) and (d) only (4) (a), (b) and (d) only
J-08818 !J-08818-PAPER-II! 11 Paper-II
Text of page 12
45. Consider the following statements regarding poles and zeros of network function.
(a) The total number of poles is equal to the total number of zeros in a rational network
function
(b) The poles and zeros of a network function determine the magnitude of the response
(c) The poles of a network function determine the waveform of the time variation of the
response
Which of the above statements are correct ?
(1) (a) and (b) only (2) (a) and (c) only
(3) (b) and (c) only (4) (a), (b) and (c)
46. Match the following :
µn Dn
(a) Ambipolar Diffusion Constant (i) µp D p
(n+p)D n D p
(b) Ambipolar Diffusion Constant of the excess carriers (ii) nD n+pD p
2D n Dp
(c) Diffusion Constant for holes (iii)
D n+Dp
Da (1+γ)
(d) Constant γ (iv) 2γ
Code :
(a) (b) (c) (d)
(1) (ii) (iii) (iv) (i)
(2) (i) (ii) (iii) (iv)
(3) (iii) (iv) (i) (ii)
(4) (iv) (i) (ii) (iii)
J-08818 !J-08818-PAPER-II! 12 Paper-II
Text of page 13
47. Match the following :
(a) P-N Junction diode (i)
(b) Zener diode (ii)
(c) Schottky diode (iii)
(d) Tunnel diode (iv)
Code :
(a) (b) (c) (d)
(1) (iii) (iv) (ii) (i)
(2) (iii) (ii) (i) (iv)
(3) (i) (ii) (iii) (iv)
(4) (ii) (iii) (iv) (i)
48. Match the following :
µ n C ox w
(a) JFET (i) (Vgs −Vin )2
2L
2IDSS V
1− GS
Vp Vp
(b) MOSFET (ii)
(c) Gunn diode (iii) q (nlµl+nu µu)
R
1+ B
RE
(d) BJT (iv) (β+1)
RB
+(β+1)
RE
Code :
(a) (b) (c) (d)
(1) (i) (ii) (iii) (iv)
(2) (ii) (i) (iii) (iv)
(3) (iii) (iv) (i) (ii)
(4) (iv) (iii) (ii) (i)
J-08818 !J-08818-PAPER-II! 13 Paper-II
Text of page 14
49. Match the following :
List-I List-II
(a) Surface potential at the (i) − 2 s q NA [V( y )+2 ψ B ]
onset of strong inversion
(b) Charge in the inversion layer (ii) VD +2 ψ B
2 s q NA (2 ψ B )
(c) Charge in the depletion region (iii) 2 ψB +
Ci
(d) Threshold voltage (iv) −VG −ψ s ( y ) C i+ 2 s q NA [V ( y )+2 ψ B ]
Code :
(a) (b) (c) (d)
(1) (i) (ii) (iii) (iv)
(2) (ii) (iv) (i) (iii)
(3) (iii) (i) (iv) (ii)
(4) (iv) (iii) (ii) (i)
50. Match the following in the context of 8257 programmable DMA controller :
List-I List-II
(The most significant two (Operations in memory mapped I/O)
bits of count register)
(a) 00 (i) Illegal
(b) 01 (ii) DMA write cycle
(c) 10 (iii) DMA verify cycle
(d) 11 (iv) DMA read cycle
Correct code are :
Code :
(a) (b) (c) (d)
(1) (i) (iii) (ii) (iv)
(2) (iii) (iv) (ii) (i)
(3) (iv) (i) (iii) (ii)
(4) (ii) (iv) (i) (iii)
J-08818 !J-08818-PAPER-II! 14 Paper-II
Text of page 15
51. Match the following Lists :
List - I List-II
(a) No. of Parallel Ports in 8051 (i) 2
(b) No. of Registers in each DMA channel of 8257 (ii) 3
(c) Type of hardware interrupts in 8085 (iii) 4
(d) No. of priority modes in 8259 (iv) 5
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iii) (i) (iv) (ii)
(2) (ii) (iii) (i) (iv)
(3) (i) (iv) (iii) (ii)
(4) (iv) (ii) (iii) (i)
52. Match the following Lists if you execute a command-line program “test” in ‘C’ as below :
test string 1 string 2.
List-I List-II
(a) argc (i) base address of ‘test’
(b) argv[0] (ii) number of arguments+1
(c) argv[1] (iii) base address of string 2
(d) argv[2] (iv) base address of string 1
Correct code are :
Code :
(a) (b) (c) (d)
(1) (ii) (i) (iv) (iii)
(2) (i) (ii) (iv) (iii)
(3) (ii) (i) (iii) (iv)
(4) (iv) (iii) (ii) (i)
J-08818 !J-08818-PAPER-II! 15 Paper-II
Text of page 16
53. Match the following Lists in FORTRAN :
List-I List-II
(a) RETURN (i) Physical end of program
(b) STOP (ii) Temporarily halt the execution
(c) PAUSE (iii) Value is received by the calling sub-program
(d) END (iv) Terminates execution
Correct code are :
Code :
(a) (b) (c) (d)
(1) (ii) (i) (iii) (iv)
(2) (iv) (ii) (i) (iii)
(3) (i) (iii) (iv) (ii)
(4) (iii) (iv) (ii) (i)
54. Match the following Lists :
List-I List-II
(a) LVDT (i) Displacement sensitive
(b) Capacitive Type Transducer (ii) Motion transducers
(c) Piezo-Electric Transducer (iii) Magnetic coupling
(d) Electromechanical Type Transducer (iv) Crystalline material
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iii) (ii) (iv) (i)
(2) (iii) (i) (iv) (ii)
(3) (ii) (iii) (iv) (i)
(4) (ii) (i) (iii) (iv)
J-08818 !J-08818-PAPER-II! 16 Paper-II
Text of page 17
55. Match the following Lists :
List - I List - II
(a) (i) Stable but oscillatory system
(b) (ii) Stable and well damped system
(c) (iii) Unstable system
(d) (iv) Marginally unstable system
Code :
(a) (b) (c) (d)
(1) (ii) (i) (iv) (iii)
(2) (ii) (iii) (i) (iv)
(3) (iv) (iii) (i) (ii)
(4) (iv) (i) (ii) (iii)
J-08818 !J-08818-PAPER-II! 17 Paper-II
Text of page 18
56. Match the following Lists :
List - I List - II
(a) (i)
(b) (ii)
(c) (iii)
(d) (iv)
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (iii) (iv) (ii) (i)
(2) (ii) (i) (iii) (iv)
(3) (ii) (i) (iv) (iii)
(4) (iv) (iii) (ii) (i)
J-08818 !J-08818-PAPER-II! 18 Paper-II
Text of page 19
57. Match the following Lists :
List-I List-II
I1 I1
V V2
(a) Open circuit parameters (i) 1
I2 I2
V V2
1
V1 V1
I V2
(b) Short circuit parameters (ii) 1
I2 I2
I V2
1
V1 V1
V −I 2
(c) Hybrid parameters (iii) 2
I1 I1
V −I 2
2
V1 V1
I I2
1
(d) Transmission parameters (iv) V2 V2
I1 I2
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (iv) (i) (ii) (iii)
(2) (iv) (ii) (iii) (i)
(3) (ii) (iii) (i) (iv)
(4) (ii) (iv) (iii) (i)
J-08818 !J-08818-PAPER-II! 19 Paper-II
Text of page 20
58. In following lists, there are materials and their band gap energies.
Match the following Lists :
List-I List-II
Material Band gap Energies (eV)
(a) GaAs (i) 0.73-1.35 eV
(b) GaAlAs (ii) 0.96-1.24 eV
(c) InGaAs (iii) 1.4-1.55 eV
(d) InGaAsP (iv) 1.4 eV
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (i) (ii) (iv) (iii)
(2) (ii) (i) (iii) (iv)
(3) (iv) (iii) (ii) (i)
(4) (i) (iii) (iv) (ii)
59. Following are the inductances for different Geometries used in Microwaves :
Match the following Lists :
List-I List-II
Inductor Inductance in(pH/mil)
(a) Wire inductor (i) L=31.25 N2D
5
(b) Circular Loop inductor (ii) L = 8.5 A (N) 3×10 3
t
(c) Square Spiral inductor (iii) L = 5.08 l ln −1.76
w+t
l
(d) Circular Spiral inductor (iv) L = 5.08 l ln +0.386
d
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (iv) (iii) (ii) (i)
(2) (i) (iii) (iv) (ii)
(3) (ii) (i) (iii) (iv)
(4) (i) (iv) (iii) (ii)
J-08818 !J-08818-PAPER-II! 20 Paper-II
Text of page 21
60. Match the following lists in terms of Electrical and Magnetic circuits :
List-I List-II
(Magnetic circuits) (Electrical circuits)
N.i
(a) (i) ∑ Vm
φ m
(b) ∑ Nm .im (ii) ∑ ik = 0
m k
1
(c) ∑ φk = 0 (iii)
ρ
V
(d) µ (iv)
i
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iv) (i) (ii) (iii)
(2) (i) (iii) (iv) (ii)
(3) (ii) (i) (iii) (iv)
(4) (i) (iv) (ii) (iii)
61. Match the following Lists :
List-I List-II
radiated power
(a) Directive Gain (i) total input power
λ2
(b) Directivity (ii) .D
4π
4π ψ
(c) Power Gain (iii) P(radiated)
(d) Effective Area (iv) 10 log10(gd)max
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (i) (ii) (iv) (iii)
(2) (iii) (iv) (i) (ii)
(3) (iv) (iii) (ii) (i)
(4) (ii) (iii) (iv) (i)
J-08818 !J-08818-PAPER-II! 21 Paper-II
Text of page 22
62. Match the following Lists :
List-I List-II
(a) ASK (i) Multiplier and an integrator
(b) Matched filter (ii) Minimizes SNR at the detection instant
(c) PSK (iii) Digital to digital encoding
(d) Correlation receiver (iv) Maximum probability of error
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iii) (ii) (i) (iv)
(2) (iv) (iii) (ii) (i)
(3) (ii) (iv) (iii) (i)
(4) (iv) (ii) (iii) (i)
63. Match the following Lists :
List-I List-II
(a) AM wave (i) Vc cos [ωct+mcos(ωmt)]
(b) FSK (ii) A cos [ω0t+φ(t)]
(c) FM wave (iii) Vc cos [2π( fc+Vm(t)∆f )t]
(d) BPSK (iv) [1+m.sin(2π fmt)] [Ec sin (2π fct)]
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iv) (ii) (i) (iii)
(2) (iii) (iv) (i) (ii)
(3) (i) (iii) (iv) (ii)
(4) (iv) (iii) (i) (ii)
64. Match the following Lists :
List-I List-II
(a) RAM (i) all data is wiped out of the stored contents
(b) EPROM (ii) act as adjunct to slower main memory
(c) E2PROM (iii) Read-write memory
(d) Cache (iv) It can be used to change certain bytes from the stored data
Correct code are :
Code :
(a) (b) (c) (d)
(1) (iii) (i) (iv) (ii)
(2) (ii) (iv) (i) (iii)
(3) (iii) (iv) (ii) (i)
(4) (iii) (iv) (i) (ii)
J-08818 !J-08818-PAPER-II! 22 Paper-II
Text of page 23
65. Match the following Lists :
List - I List - II
(a) (i)
(b) (ii)
(c) (iii)
(d) (iv)
Correct codes are :
Code :
(a) (b) (c) (d)
(1) (ii) (i) (iv) (iii)
(2) (iii) (iv) (ii) (i)
(3) (ii) (iv) (i) (iii)
(4) (iii) (iv) (i) (ii)
J-08818 !J-08818-PAPER-II! 23 Paper-II
Text of page 24
66. The following semiconductor material are given
(a) C (b) Si (c) GaAs (d) InP
Arrange the above in the increasing order of their Hole Mobility at 300 K.
Options :
(1) (a), (b), (c), (d)
(2) (b), (c), (d), (a)
(3) (c), (d), (a), (b)
(4) (d), (c), (b), (a)
67. Arrange the following amplifier in the increasing order of their Current Gain.
(a) Common-emitter amplifier
(b) Common-base amplifier
(c) Darlington amplifier in common-emitter configuration
(d) Common-collector amplifier
Options :
(1) (b), (a), (d), (c)
(2) (a), (b), (c), (d)
(3) (c), (d), (a), (b)
(4) (d), (c), (b), (a)
68. Arrange the following pins of 8086 µp in the descending order :
(a) INTR (b) AD o (c) MN/ MX (d) LOCK
The correct sequence is :
(1) (b), (c), (a), (d)
(2) (c), (d), (a), (b)
(3) (d), (b), (c), (a)
(4) (a), (d), (b), (c)
69. What is the correct sequence of the following operators in ‘C’ from highest to lowest precedence
order ?
(a) == (b) %= (c) % (d) <=
The correct sequence is :
(1) (c), (b), (a), (d)
(2) (c), (a), (d), (b)
(3) (c), (d), (a), (b)
(4) (a), (b), (d), (c)
J-08818 !J-08818-PAPER-II! 24 Paper-II
Text of page 25
70. Following are the semiconductor materials having certain values of recombination co-efficients.
Arrange them in terms of ascending order :
(a) GaP (b) Si (c) InAs (d) GaAs
The correct sequence in ascending order of their values are :
(1) (b), (a), (c), (d)
(2) (d), (b), (a), (c)
(3) (a), (b), (c), (d)
(4) (c), (b), (a), (d)
71. Following transmission media are given :
(a) Twisted pair cables (b) Optical fiber cables
(c) Coaxial cables (d) Microwaves
For high rate data transmission systems, arrange the above in terms of their Losses in ascending
orders.
The correct sequence is given by :
(1) (b), (c), (a), (d)
(2) (d), (c), (a), (b)
(3) (a), (b), (c), (d)
(4) (b), (d), (c), (a)
72. Consider the following circuits :
(a) Integrating circuit
(b) Active differentiation circuit
(c) Notch type electrical filter
Arrange the above circuit models in decreasing order of their complexity.
(1) (a), (b), (c)
(2) (a), (c), (b)
(3) (b), (c), (a)
(4) (c), (b), (a)
J-08818 !J-08818-PAPER-II! 25 Paper-II
Text of page 26
73. Consider the following network :
(a) Power dissipated in resistor R1 is P1
(b) Power dissipated in resistor R2 is P2
(c) Power dissipated in resistor R3 is P3
Arrange the above in increasing order of the dissipated power :
(1) (a), (c), (b)
(2) (a), (b), (c)
(3) (b), (c), (a)
(4) (c), (a), (b)
74. Consider the following systems :
(a) Satellite
(b) Conventional Public Address System
(c) Conventional Radio Receiver
(d) Laser detector
Arrange the above systems in order of their increasing order of operational frequency :
(1) (c), (b), (a), (d)
(2) (b), (c), (d), (a)
(3) (a), (b), (c), (d)
(4) (b), (c), (a), (d)
75. Consider the following logic families :
(a) Standard TTL logic family
(b) ECL - logic family
(c) RTL - logic family
(d) CMOS - logic family
Arrange the above logic families in order of their decreasing power dissipation :
(1) (b), (c), (d) and (a)
(2) (b), (c), (a) and (d)
(3) (c), (b), (a) and (d)
(4) (c), (b), (d) and (a)
J-08818 !J-08818-PAPER-II! 26 Paper-II
Text of page 27
Directions : Questions 76 to 95.
The following items consist of two statements, one labelled as “Assertion(A)” and the other
labelled as “Reason(R)”. You are to examine the two statements carefully and decide if the
Assertion(A) and the Reason(R) are individually true and if so whether the reason is a
correct explanation of the assertion. Select your answer to these items using the codes given
below and mark your answer accordingly.
Code :
(1) Both (A) and (R) are true and (R) is the correct explanation of (A).
(2) Both (A) and (R) are true, but (R) is not the correct explanation of (A).
(3) (A) is true, but (R) is false.
(4) (A) is false, but (R) is true.
76. Assertion (A) : In a p-n junction the electron crossing the junction from right to left constitute
a current in the same direction as hole crossing the junction from left to
right.
Reason (R) : In a p-n junction the low value of depletion region capacitance can be
obtained with reverse biasing.
77. Assertion (A) : For integrated circuit production the line width limit of optical Lithography
lies near 0.4 µm, although 0.2 µm feature may eventually be printed under
carefully controlled conditions.
Reason (R) : A negative resist on exposure to light becomes less soluble in a developer
solution, while a positive resist becomes more soluble.
78. Assertion (A) : The total gain of a cascaded system is determined by the product of the
gains of each stage.
Reason (R) : The gain of each stage must be determined under loaded conditions.
79. Assertion (A) : The tunnel diode shows the negative differential resistance between peak
voltage and valley voltage.
Reason (R) : In a tunnel diode, for a voltage larger than valley voltage, the current
increases exponentially.
80. Assertion (A) : A two byte instruction of 8085 has an operation code in first byte and
operand/address in the second byte.
Reason (R) : Source and destination addresses are made implicit in order to reduce the
length of an instruction.
J-08818 !J-08818-PAPER-II! 27 Paper-II
Text of page 28
81. Assertion (A) : In 8086 µp, ALE is provided by the processor to latch the address into the
8282/8283 address latch.
Reason (R) : Whenever the processor sends a valid address on the multiplexed
AD0-AD15 lines, it also makes the ALE high.
82. Assertion (A) : In ‘C’, bit fields cannot be used in a union.
Reason (R) : If one element of union is initialized then it also initializes other elements of
the union.
83. Assertion (A) : Encapsulation is implemented by a ‘class’ in C++.
Reason (R) : Private, public and protected access specifiers are used.
84. Assertion (A) : The magnetic flux per unit length through a loop of small length is called
the magnetic flux density.
Reason (R) : The direction of magnetic flux density is taken as the normal to the plane of
the loop when oriented to enclose maximum flux.
λ
85. Assertion (A) : For transmission lines, having their length equal to odd multiples of ,
4
the following expressions are given
sin βL=±1 and cos βL=0.
Reason (R) : Under the above conditions, i.e. for odd multiples of Quarter wavelengths
Z .cosh (α L)
the input impedance becomes equal to Z = 0 .
sinh (α L)
86. Assertion (A) : The z-parameters are open circuit parameters.
Reason (R) : The z-parameters may be measured at one terminal while the other terminal
is open.
87. Assertion (A) : All the mesh currents are necessarily the loop currents but all the loop
currents may not be the mesh current.
Reason (R) : The mesh current is the current which flows only around the perimeter of a
mesh.
J-08818 !J-08818-PAPER-II! 28 Paper-II
Text of page 29
88. Assertion (A) : Vestigial side band gives rise to frequencies very close to the carrier frequency.
Reason (R) : It is not possible to go to extreme and suppress one complete side band by
physically realizable filters.
89. Assertion (A) : Lesser number of bits per code are required due to less number of
quantization levels in DPCM.
Reason (R) : In this case, the difference between two successive samples is quantized
which do not differ much in amplitude.
90. Assertion (A) : The hexadecimal numbers are first converted into binary numbers and
operations are performed using binary representation of hexadecimal
numbers using rules of binary numbers.
Reason (R) : The information can be handled in hexadecimal form in digital circuits but
it is easier to enter information using binary numbers.
91. Assertion (A) : Emitter - Coupled Logic (ECL) is the fastest of all logic families and used in
applications where very high speed is essential.
Reason (R) : High speed in ECL is because the transistors are used in difference amplifier
configuration in which they are never driven into saturation and the storage
time is eliminated.
92. Assertion (A) : The synchronous speed of an induction motor can be varied by varying the
frequency of the applied voltage.
Reason (R) : With smaller frequency of operation, there is a large value of slip and motor
rotates non-linearly with the frequency ‘f ’ of the applied voltage.
93. Assertion (A) : The diameter of SMF is selected in such a way that single fundamental ray
travels straight along the axis of the core of the fiber.
Reason (R) : The diameter of core of SMF is more than 10 µm and outer diameter is less
than 125 µm.
J-08818 !J-08818-PAPER-II! 29 Paper-II
Text of page 30
94. Assertion (A) : The stability analysis of systems with dead time can be conducted easily
using the Bode plots.
Reason (R) : The magnitude plot of a system is unaffected by the presence of dead time.
95. Assertion (A) : A Non-Return to Zero (NRZ) type digital recording system is more common
and efficient.
Reason (R) : It is possible to record twice the number of digits for the same number of
pulses.
Based on the following para, answer Q.No. 96 to 100.
Sensitivity considerations often are important in the design of Control Systems. Because all
physical elements have properties that change with environment and age, we cannot always
consider the parameters of the Control System to be completely stationary over the entire
operating life of the system. For instance, the winding resistance of an electric motor changes
as the temperature of the motor rises during operation. Control systems with electric
components may not operate normally when first turned on because of the still-changing
system parameters during warmup. This phenomenon is sometimes called “morning
sickness”. Most duplicating machines have a warmup period during which time operation
is blocked out when first turn on.
96. Which of the following statements is correct ?
(1) A feedback can only increase the sensitivity of a system
(2) A feedback can increase or decrease the sensitivity of a system
(3) A feedback can only decrease the sensitivity of a system
(4) A feedback never affects the sensitivity of a system
97. A good Control System should be :
(a) Very sensitive to parameter variations
(b) Insensitive to parameter variations
(c) Insensitive to input commands
(d) Sensitive to input commands
Which of the above are correct ?
(1) (a) and (b) (2) (b) and (c)
(3) (b) and (d) (4) (a) and (d)
25
98. The open-loop transfer function of a Unity Feedback Control System is given by G(s) = .
s(s + 5)
The steady state error will be :
(1) 0.1 rad (2) 0.2 rad (3) 0.3 rad (4) 0.5 rad
J-08818 !J-08818-PAPER-II! 30 Paper-II
Text of page 31
99. The sensitivity of the overall (closed-loop) transfer function for the system shown below,
with respect to forward path transfer function at ω=1 rad/sec will be :
(1) 0.938 (2) 0.583 (3) 0.25 (4) 0.398
100. For an open-loop control system, sensitivity of overall transfer function M(s) with respect to
forward path transfer function G(s) will be :
(1) 1 (2) 0 (3) −1 (4) ∞
-oOo-
J-08818 !J-08818-PAPER-II! 31 Paper-II
Text of page 32
Space For Rough Work J-08818 !J-08818-PAPER-II! 32 Paper-II
Official key not published for this paper.
Page 1 of 32
Source: University Grants Commission. Question paper published by University Grants Commission.