Networking Basics Questions and Answers

Q: Three or more devices share a link in ________ connection:

Correct answer: MultipointIn a multipoint, or multidrop, connection more than two devices share a single link, so the capacity is shared - spatially if they can transmit at once, or in time if they must take turns. A point-to-point connection dedicates the whole link to two devices. Simplex describes the direction of flow rather than the number of devices, so it answers a different question altogether.

Q: Which of the following computer networks is built on the top of another network?

Correct answer: overlay networkAn overlay network is built as a logical topology on top of an existing physical one: its links are paths, possibly many hops long, through the underlying network. Peer-to-peer systems, VPNs and content distribution networks are all overlays. The advantage is that new services can be deployed without changing the infrastructure beneath; the cost is that the overlay cannot see the real topology and may route inefficiently across it.

Q: Communication channel is shared by all the machines on the network in:

Correct answer: broadcast networkIn a broadcast network a single communication channel is shared by every machine, so a frame sent by one is received by all and each decides from the address field whether the frame is meant for it. Classic Ethernet on a hub and wireless LANs work this way, which is why they need a media access control method. Unicast and multicast describe the intended set of recipients of a particular transmission, not how the channel itself is arranged.

Q: What command will display the line, protocol, DLCI, and LMI information of an interface?

Correct answer: show interfaceshow interface reports the line status and line protocol status, and on a Frame Relay interface it also shows the LMI type and DLCI information. show frame-relay pvc gives fuller PVC detail - the DLCI status and the congestion counters - but not the line and protocol status of the interface itself, which is why the single interface command is the one that covers all four items asked for.

Q: If your router is facilitating a CSU/DSU, which of the following commands do you need to use to provide the router with a 64000bps serial link?

Correct answer: RouterA(config-if)#clock rate 64000Where the router provides the DCE function it must supply the clocking, and clock rate is set in bits per second under the interface, hence 64000 rather than 64. bandwidth is a quite different command: it sets a value used by routing protocols in their metric calculations and by QoS, and changing it has no effect whatever on the actual line speed.

Q: The structure or format of data is called:

Correct answer: SyntaxSyntax is the structure or format of the data - the order of the fields, the number of bits in each, where the address sits and where the payload begins. Semantics is what those bits mean and what action they call for; timing concerns when data may be sent and how fast. The three together make up a protocol, and this question isolates the first of them.

Q: What are the two main types of access control lists (ACLs)? 1.Standard 2.IEEE 3.Extended 4.Specialized

Correct answer: 1 and 3The two main types are standard and extended. A standard access list filters on the source address only and is placed close to the destination; an extended list filters on source and destination address, protocol and port, and is placed close to the source so that unwanted traffic is dropped before it crosses the network. IEEE and Specialized are not access list types at all.

Q: What command is used to create a backup configuration?

Correct answer: copy running-config startup-configThe running configuration lives in RAM and is lost at reload; the startup configuration lives in NVRAM and is what the router reads on boot. Copying one to the other saves the current settings, and the abbreviation copy run start is the form most often typed. The older write memory did the same job on earlier IOS versions and survives as a deprecated alias, but the copy form is the current command.

161.

Two devices are in network if:

A.a process in one device is able to exchange information with a process in another device
B.a process is running on both devices
C.PIDs of the processes running of different devices are same
D.none of the mentioned

Answer: A

Correct answer: a process in one device is able to exchange information with a process in another device

Networking is defined by the ability to exchange information, not by any similarity between the machines. Two devices are networked when a process on one can communicate with a process on the other, whatever their hardware, operating systems or process identifiers. Process IDs are local to each machine and carry no meaning across a network, and both devices running a process is neither necessary nor sufficient.

Discuss in Forum

162.

Three or more devices share a link in ________ connection:

A.Unipoint
B.Multipoint
C.Point to point
D.None of the mentioned

Answer: B

Correct answer: Multipoint

In a multipoint, or multidrop, connection more than two devices share a single link, so the capacity is shared - spatially if they can transmit at once, or in time if they must take turns. A point-to-point connection dedicates the whole link to two devices. Simplex describes the direction of flow rather than the number of devices, so it answers a different question altogether.

Discuss in Forum

163.

Which of the following computer networks is built on the top of another network?

A.prior network
B.chief network
C.prime network
D.overlay network

Answer: D

Correct answer: overlay network

An overlay network is built as a logical topology on top of an existing physical one: its links are paths, possibly many hops long, through the underlying network. Peer-to-peer systems, VPNs and content distribution networks are all overlays. The advantage is that new services can be deployed without changing the infrastructure beneath; the cost is that the overlay cannot see the real topology and may route inefficiently across it.

Discuss in Forum

164.

Which one of the following is true regarding VLANs?

A.Two VLANs are configured by default on all Cisco switches.
B.VLANs only work if you have a complete Cisco switched internetwork. No off-brand switches are allowed.
C.You should not have more than 10 switches in the same VTP domain.
D.VTP is used to send VLAN information to switches in a configured VTP domain.

Answer: D

Correct answer: VTP is used to send VLAN information to switches in a configured VTP domain.

VLAN Trunking Protocol propagates the VLAN database from a server switch to the clients in the same VTP domain, so a VLAN created once appears throughout. The other statements are false: only VLAN 1 exists by default, not two; VLANs are a standard function that works with equipment from any manufacturer; and there is no ten-switch limit on a VTP domain.

Discuss in Forum

165.

Communication channel is shared by all the machines on the network in:

A.broadcast network
B.unicast network
C.multicast network
D.none of the mentioned

Answer: A

Correct answer: broadcast network

In a broadcast network a single communication channel is shared by every machine, so a frame sent by one is received by all and each decides from the address field whether the frame is meant for it. Classic Ethernet on a hub and wireless LANs work this way, which is why they need a media access control method. Unicast and multicast describe the intended set of recipients of a particular transmission, not how the channel itself is arranged.

Discuss in Forum

166.

What command will display the line, protocol, DLCI, and LMI information of an interface?

A.sh pvc
B.show interface
C.show frame-relay pvc
D.show run

Answer: B

Correct answer: show interface

show interface reports the line status and line protocol status, and on a Frame Relay interface it also shows the LMI type and DLCI information. show frame-relay pvc gives fuller PVC detail - the DLCI status and the congestion counters - but not the line and protocol status of the interface itself, which is why the single interface command is the one that covers all four items asked for.

Discuss in Forum

167.

If your router is facilitating a CSU/DSU, which of the following commands do you need to use to provide the router with a 64000bps serial link?

A.RouterA(config)#bandwidth 64
B.RouterA(config-if)#bandwidth 64000
C.RouterA(config-if)#clock rate 64
D.RouterA(config-if)#clock rate 64000

Answer: D

Correct answer: RouterA(config-if)#clock rate 64000

Where the router provides the DCE function it must supply the clocking, and clock rate is set in bits per second under the interface, hence 64000 rather than 64. bandwidth is a quite different command: it sets a value used by routing protocols in their metric calculations and by QoS, and changing it has no effect whatever on the actual line speed.

Discuss in Forum

168.

The structure or format of data is called:

A.Syntax
B.Semantics
C.Struct
D.None of the mentioned

Answer: A

Correct answer: Syntax

Syntax is the structure or format of the data - the order of the fields, the number of bits in each, where the address sits and where the payload begins. Semantics is what those bits mean and what action they call for; timing concerns when data may be sent and how fast. The three together make up a protocol, and this question isolates the first of them.

Discuss in Forum

169.

What are the two main types of access control lists (ACLs)?

1.Standard

2.IEEE

3.Extended

4.Specialized

A.1 and 3
B.2 and 4
C.3 and 4
D.1 and 2

Answer: D

Correct answer: 1 and 3

The two main types are standard and extended. A standard access list filters on the source address only and is placed close to the destination; an extended list filters on source and destination address, protocol and port, and is placed close to the source so that unwanted traffic is dropped before it crosses the network. IEEE and Specialized are not access list types at all.

Discuss in Forum

170.

What command is used to create a backup configuration?

A.copy running backup
B.copy running-config startup-config
C.config mem
D.wr mem

Answer: B

Correct answer: copy running-config startup-config

The running configuration lives in RAM and is lost at reload; the startup configuration lives in NVRAM and is what the router reads on boot. Copying one to the other saves the current settings, and the abbreviation copy run start is the form most often typed. The older write memory did the same job on earlier IOS versions and survives as a deprecated alias, but the copy form is the current command.

Discuss in Forum

Loading…

Topics

Other Subjects

Tags: Networking Basics Questions and Answers || Networking Basics MCQ Questions and Answers || Networking Basics GK Questions and Answers || Networking Basics GK MCQ Questions || Networking Basics Multiple Choice Questions and Answers || Networking Basics GK || GK on Networking Basics || Computer Networking Questions and Answers || Computer Networking MCQ Questions and Answers || Computer Networking GK Questions and Answers || GK on Computer Networking

Networking Basics Questions and Answers

Topics

Other Subjects

About Us

Stay informed about all important Dates & Notifications