Match List I with List II and select the correct answer using the codes given below :List IList II(a) TCON(i) contains status information(b) SBUF(ii) timer/counter control register(c) TMOD(iii) idle bit, power down bit(d) PSW(iv) serial data buffer for \(T_x\) and \(R_x\)(e) PCON(v) timer/counter modes of operation

The correct matching is a-ii, b-iv, c-v, d-i, e-iii.TCON is the timer/counter control register, with the run and overflow flags (ii).SBUF is the serial data buffer for transmission and reception (iv).TMOD selects the timer/counter modes of operation (v).PSW, the program status word, contains status information such as the carry, auxiliary carry, overflow and parity flags (i).PCON, the power control register, contains the idle and power-down bits (iii).The other codes confuse TCON with TMOD or give PSW the power control bits.

Match the following :List IList II(1) TCON(i) contains status information(2) SBUF(ii) timer/counter control register(3) TMOD(iii) idle bit, power down bit(4) PSW(iv) serial data buffer for Tx and Rx(5) PCON(v) timer/counter modes of operation

The correct match is 1-ii, 2-iv, 3-v, 4-i, 5-iii.TCON: timer/counter control register, holding the run and overflow flags of the timers and the external interrupt flags (ii).SBUF: serial data buffer, used for both transmitting and receiving (iv).TMOD: timer/counter mode register, selecting the mode of operation of each timer (v).PSW: program status word, holding status flags such as carry, auxiliary carry, overflow and parity, and the register bank select bits (i).PCON: power control register, with the idle and power-down bits and SMOD (iii).Each of the other options mismatches TCON with status or modes, or SBUF with mode bits, which these 8051 registers do not hold.

8051 Microcontroller Architecture Questions and Answers

Q: If no key is pressed microcontroller 8051 port will read :

With no key pressed an 8051 port reads 1.Ports 1, 2 and 3 of the 8051 have internal pull-up resistors, and a pin written with 1 is configured as an input pulled high. A key is normally wired between the port pin and ground, so pressing it pulls that pin to 0. With no key pressed, nothing pulls the pin down and it reads logic 1 (and an all-released port reads FFH).A 0 would be read only while a key is pressed. 'NC' means no connection and is not a logic level, and 7 is not a value a single port bit can take.

Q: What is the Address (SFR) for TCON, SCON, SBUF, PCON and PSW respectively ?

The addresses are 88H, 98H, 99H, 87H, 0D0H.In the 8051's special function register space:TCON, timer control: 88HSCON, serial control: 98HSBUF, serial buffer: 99HPCON, power control: 87HPSW, program status word: D0H, written 0D0H in assembly so it starts with a digitThe other options list the same five addresses in a different order. Option B puts SCON at 88H, which is TCON's address; option C starts with PSW's address; and option D starts with PCON's 87H for TCON. A useful check is that the bit-addressable registers, TCON, SCON and PSW, all sit at addresses ending in 0 or 8.

Q: Which of the following should a microcontroller at least consist of :

A microcontroller must at least have CPU, RAM, ROM, I/O ports and Timers.The defining feature of a microcontroller, as against a microprocessor, is that it is a computer on a single chip: the processor core together with program memory (ROM or flash), data memory (RAM), input/output ports and timers/counters. The 8051, for example, combines a CPU, 4 KB ROM, 128 bytes RAM, four I/O ports and two timers.Each of the other options leaves one component out: A has no RAM, B has no CPU, and C has no ROM to hold the program. Only option D lists all of them.

Q: If the ............. pin is .........., then we have the option of using the ......... ROM or EPROM together with ....... memory and devices.

The answer is EA, high, internal, external.The 8051's EA (External Access) pin selects where the program comes from. When EA is connected high (to VCC), the 8051 fetches code from its internal ROM or EPROM for the lower addresses (the first 4 KB in the 8051) and automatically uses external memory for addresses beyond it, so internal and external memory can be used together.When EA is tied low, the internal ROM is ignored and all program fetches go to external memory. Options with EA low therefore cannot give the use of internal ROM, and the option with 'high, external, internal' reverses which memory is used first.

11.

Match List I with List II and select the correct answer using the codes given below :

List I	List II
(a) TCON	(i) contains status information
(b) SBUF	(ii) timer/counter control register
(c) TMOD	(iii) idle bit, power down bit
(d) PSW	(iv) serial data buffer for \(T_x\) and \(R_x\)
(e) PCON	(v) timer/counter modes of operation

A.a-ii, b-iv, c-v, d-i, e-iii
B.a-i, b-v, c-iv, d-iii, e-ii
C.a-v, b-iii, c-ii, d-iv, e-i
D.a-iii, b-ii, c-i, d-v, e-iv

Exam Year(s)

MH SET - 2023, SET Exam - 2023,

Answer: A

The correct matching is a-ii, b-iv, c-v, d-i, e-iii.

TCON is the timer/counter control register, with the run and overflow flags (ii).
SBUF is the serial data buffer for transmission and reception (iv).
TMOD selects the timer/counter modes of operation (v).
PSW, the program status word, contains status information such as the carry, auxiliary carry, overflow and parity flags (i).
PCON, the power control register, contains the idle and power-down bits (iii).

The other codes confuse TCON with TMOD or give PSW the power control bits.

Discuss in Forum

12.

If no key is pressed microcontroller 8051 port will read :

A.0
B.1
C.NC
D.7

Exam Year(s)

MH SET - 2024, SET Exam - 2024,

Answer: B

With no key pressed an 8051 port reads 1.

Ports 1, 2 and 3 of the 8051 have internal pull-up resistors, and a pin written with 1 is configured as an input pulled high. A key is normally wired between the port pin and ground, so pressing it pulls that pin to 0. With no key pressed, nothing pulls the pin down and it reads logic 1 (and an all-released port reads FFH).

A 0 would be read only while a key is pressed. 'NC' means no connection and is not a logic level, and 7 is not a value a single port bit can take.

Discuss in Forum

13.

What is the Address (SFR) for TCON, SCON, SBUF, PCON and PSW respectively ?

A.88H, 98H, 99H, 87H, 0D0H
B.98H, 99H, 87H, 88H, 0D0H
C.0D0H, 87H, 88H, 99H, 98H
D.87H, 88H, 0D0H, 98H, 99H

Exam Year(s)

MH SET - 2024, SET Exam - 2024,

Answer: A

The addresses are 88H, 98H, 99H, 87H, 0D0H.

In the 8051's special function register space:

TCON, timer control: 88H
SCON, serial control: 98H
SBUF, serial buffer: 99H
PCON, power control: 87H
PSW, program status word: D0H, written 0D0H in assembly so it starts with a digit

The other options list the same five addresses in a different order. Option B puts SCON at 88H, which is TCON's address; option C starts with PSW's address; and option D starts with PCON's 87H for TCON. A useful check is that the bit-addressable registers, TCON, SCON and PSW, all sit at addresses ending in 0 or 8.

Discuss in Forum

14.

Which of the following should a microcontroller at least consist of :

A.CPU, ROM, I/O ports and Timers
B.RAM, ROM, I/O ports and Timers
C.CPU, RAM, I/O ports and Timers
D.CPU, RAM, ROM, I/O ports and Timers

Exam Year(s)

MH SET - 2024, SET Exam - 2024,

Answer: D

A microcontroller must at least have CPU, RAM, ROM, I/O ports and Timers.

The defining feature of a microcontroller, as against a microprocessor, is that it is a computer on a single chip: the processor core together with program memory (ROM or flash), data memory (RAM), input/output ports and timers/counters. The 8051, for example, combines a CPU, 4 KB ROM, 128 bytes RAM, four I/O ports and two timers.

Each of the other options leaves one component out: A has no RAM, B has no CPU, and C has no ROM to hold the program. Only option D lists all of them.

Discuss in Forum

15.

Match the following :

List I	List II
(1) TCON	(i) contains status information
(2) SBUF	(ii) timer/counter control register
(3) TMOD	(iii) idle bit, power down bit
(4) PSW	(iv) serial data buffer for Tx and Rx
(5) PCON	(v) timer/counter modes of operation

A.1-ii, 2-iv, 3-v, 4-i, 5-iii
B.1-i, 2-v, 3-iv, 4-iii, 5-ii
C.1-v, 2-iii, 3-ii, 4-iv, 5-i
D.1-iii, 2-ii, 3-i, 4-v, 5-iv

Exam Year(s)

MH SET - 2025, SET Exam - 2025,

Answer: A

The correct match is 1-ii, 2-iv, 3-v, 4-i, 5-iii.

TCON: timer/counter control register, holding the run and overflow flags of the timers and the external interrupt flags (ii).
SBUF: serial data buffer, used for both transmitting and receiving (iv).
TMOD: timer/counter mode register, selecting the mode of operation of each timer (v).
PSW: program status word, holding status flags such as carry, auxiliary carry, overflow and parity, and the register bank select bits (i).
PCON: power control register, with the idle and power-down bits and SMOD (iii).

Each of the other options mismatches TCON with status or modes, or SBUF with mode bits, which these 8051 registers do not hold.

Discuss in Forum

16.

If the ............. pin is .........., then we have the option of using the ......... ROM or EPROM together with ....... memory and devices.

A.EA, high, internal, external
B.EA, low, internal, external
C.EA, high, external, internal
D.EA, low, external internal

Exam Year(s)

MH SET - 2025, SET Exam - 2025,

Answer: B

The answer is EA, high, internal, external.

The 8051's EA (External Access) pin selects where the program comes from. When EA is connected high (to V_CC), the 8051 fetches code from its internal ROM or EPROM for the lower addresses (the first 4 KB in the 8051) and automatically uses external memory for addresses beyond it, so internal and external memory can be used together.

When EA is tied low, the internal ROM is ignored and all program fetches go to external memory. Options with EA low therefore cannot give the use of internal ROM, and the option with 'high, external, internal' reverses which memory is used first.

Discuss in Forum

17.

In 8051, Pin 30 (ALE / \(\overline{\text{PROG}}\)), if this bit is set as logic zero (‘0’), it signifies

A.Address is latched
B.For enabling internal ROM of programming
C.For disabling internal ROM programming
D.Both (A) and (C)

Exam Year(s)

UGC NET - 2012,

Answer: B

The key takes the answer as option (B), for enabling the internal ROM for programming. Pin 30 of the 8051 is ALE, which is used as the address latch enable during normal work. The same pin takes the programming pulse, PROG, with an overbar because it is active low, when the on-chip program memory is being programmed. The key reads a logic zero on this pin as the condition that enables programming of the internal ROM. Option (A), address is latched, belongs to the ALE function when it is high. Option (C), disabling programming, is the opposite of the key. Option (D) combines (A) and (C). The wording of the item is loose, so it follows the key.

Discuss in Forum

Direction for [ Question No: 18 To 18 ] :

Directions : The following items consist of two statements, one labelled the "Assertion (A)" and the other labelled the "Reason (R)". You are to examine these two statements carefully and decide if the Assertion (A) and the Reason (R) are individually true and if so, whether the Reason is a correct explanation of the Assertion. Select your answers to these items using the codes given below and mark your answer accordingly.

18.

Assertion (A) : Microcontrollers are preferred in Real time applications.

Reason (R) : The on chip I/O integration has no bearing on the speed of microcontroller.

A.Both (A) and (R) are true and (R) is the correct explanation of (A).
B.Both (A) and (R) are true, but (R) is not correct explanation of (A).
C.(A) is true, but (R) is false.
D.(A) is false, but (R) is true.

Exam Year(s)

UGC NET - 2012,

Answer: C

The assertion is true and the reason is false (option C). Microcontrollers are preferred in real-time applications because the processor, memory, timers, interrupts and I/O are on one chip and so respond quickly and predictably.

The reason says that the on-chip I/O integration has no bearing on speed, which is wrong: the integration is what removes slow external buses and gives short response times. Options A and B accept the reason, and D rejects the assertion.

Discuss in Forum

19.

The following are features of a micro controller 8051 :

(i) 4 k bytes of ROM or EPROM
(ii) 128 k bytes of data memory
(iii) Four programmable I/O ports
(iv) Three 16 bit timer/event counters.

A.(i), (ii) and (iii)
B.(i), (ii) and (iv)
C.(i), (iii) and (iv)
D.(ii), (iii) and (iv)

Exam Year(s)

UGC NET - 2013,

Answer: A

The key accepts (i), (ii) and (iii), the first option. The 8051 has 4 k bytes of on-chip ROM or EPROM, four programmable 8-bit I/O ports, and a block of on-chip data memory, which in the 8051 is 128 bytes, and this is the statement meant in (ii).

Statement (iv) is wrong for the 8051, which has two 16-bit timer or event counters and not three, the third timer being a feature of the 8052. So the options containing (iv) are wrong.

Discuss in Forum

20.

Match the following lists :

List - I	List - II
a. IC 8051	i. Stack
b. Nonmaskable	ii. Implied addressing mode
c. PUSH	iii. TRAP
d. CMA	iv. Microcontroller

A.iv iii i ii
B.iv ii i iii
C.iii i ii iv
D.ii iii iv i

Exam Year(s)

UGC NET - 2013,

Answer: A

The correct match is IC 8051 with microcontroller (iv), non-maskable with TRAP (iii), PUSH with stack (i) and CMA with implied addressing mode (ii), which is the code iv iii i ii, option (A).

The 8051 is a microcontroller, TRAP is the non-maskable interrupt of the 8085, PUSH puts data on the stack, and CMA (complement accumulator) needs no operand, so it uses implied addressing. Options B, C and D pair some of these wrongly.

Discuss in Forum

Loading…

Topics

Other Subjects

Tags: 8051 Microcontroller Architecture Questions and Answers || 8051 Microcontroller Architecture MCQ Questions and Answers || 8051 Microcontroller Architecture GK Questions and Answers || 8051 Microcontroller Architecture GK MCQ Questions || 8051 Microcontroller Architecture Multiple Choice Questions and Answers || 8051 Microcontroller Architecture GK || GK on 8051 Microcontroller Architecture || Microprocessors and Microcontrollers Questions and Answers || Microprocessors and Microcontrollers MCQ Questions and Answers || Microprocessors and Microcontrollers GK Questions and Answers || GK on Microprocessors and Microcontrollers

8051 Microcontroller Architecture Questions and Answers

Direction for [ Question No: 18 To 18 ] :

Topics

Other Subjects

About Us

Stay informed about all important Dates & Notifications