Match List I with List II and select the correct answer using codes given below :List IList II(a) Electron microscope(i) Electron gun(b) Oscilloscope(ii) Condensing magnetic lens(c) Galvanometric recorder(iii) Recording head(d) Magnetic recorder(iv) Drive motor

The correct matching is a-ii, b-i, c-iv, d-iii.An electron microscope focuses its beam with a condensing magnetic lens (ii).An oscilloscope (cathode ray tube) produces its beam with an electron gun (i).A galvanometric strip-chart recorder uses a drive motor to move the chart paper at a fixed speed (iv).A magnetic recorder writes and reads the tape through a recording head (iii).Both instruments in the first two rows have an electron gun and focusing, so the pairing turns on the part each is best known for: the electron microscope's distinctive element is its magnetic lens system. The codes giving the oscilloscope a recording head or a drive motor do not fit.

Cathode Ray Oscilloscope Questions and Answers

Q: If rise time of input amplifier is 10 nsec and the observed rise time on CRO is 15 nsec, then the appropriate rise time of the signal is ________.

The rise time of the signal is about 11.18 nsec.When a signal passes through an amplifier, their rise times combine as the square root of the sum of squares: \(t_{obs}^{2} = t_{sig}^{2} + t_{amp}^{2}\).\[ \begin{aligned} t_{sig} &= \sqrt{15^{2} - 10^{2}} \\ &= \sqrt{125} = 11.18\ \text{nsec} \end{aligned} \]18.02 nsec adds the squares instead of subtracting them, 15 nsec ignores the amplifier, and 10 nsec is the amplifier's own rise time.

Q: DSO cannot be used for :

A DSO cannot be used for signal generation.A digital storage oscilloscope samples an input signal, digitises it with an ADC and stores the samples in memory, so it can display, monitor, store and analyse the signal, including measurements and FFT spectra.It is a measuring instrument with inputs only; it does not generate signals. Signals are produced by function generators, signal generators or arbitrary waveform generators. Signal analysis, monitoring and digitisation are all things a DSO does.

Q: A spectrum analyser is an instrument used for :

A spectrum analyser is used for identifying dominant frequencies and harmonics.A spectrum analyser displays signal amplitude against frequency, so it shows the frequency components of a signal: the fundamental, its harmonics, spurious signals and the noise floor.Visualising the time variation of a waveform is the job of an oscilloscope. A spectrum analyser displays the noise floor but does not introduce it. Impedance is measured with an impedance analyser or LCR meter.

Q: Lissajous figure corresponding to phase difference of 3π/4 is :

The Lissajous figure for a phase difference of 3π/4 is (D), an ellipse tilted to fall to the right.With equal frequencies and amplitudes on both axes, the pattern is a straight line rising to the right at zero phase difference, an ellipse rising to the right between 0 and π/2, a circle at π/2, and an ellipse falling to the right between π/2 and π, closing to a falling straight line at π.3π/4 (135°) lies between π/2 and π, so the ellipse leans the other way, as in figure (D). Figure (A), a rising line, is 0 phase difference; figure (B), a circle, is π/2; figure (C), an ellipse rising to the right, is π/4.

Q: Which of the following can store, manipulate and retrieve waveform related information ?

The instrument is the DSO, the digital storage oscilloscope.A DSO samples the input with an analog-to-digital converter and stores the samples in memory. The stored waveform can then be displayed, measured, processed (zoomed, averaged, transformed) and recalled or transferred to a computer later, even for a single event that does not repeat.An analog CRO displays the waveform only while it is present and cannot store it. A DMM measures single values such as voltage and current, not waveforms. A spectrum analyser displays the frequency content of a signal rather than storing the waveform itself.

Q: The sweep generator of a CRO is used to produce :

The sweep generator produces a sawtooth voltage for the horizontal deflection of the electron beam.The time base must move the spot across the screen from left to right at a constant speed, so that horizontal distance represents time, and then return it quickly to the left to start again. A sawtooth does exactly this: a linear ramp for the trace and a fast drop for the retrace. It is applied to the horizontal (X) deflection plates.The vertical plates receive the signal under observation, from the vertical amplifier, not the sweep. A sinusoidal sweep would move the spot at a varying speed and distort the time scale, so it is used only in special cases such as Lissajous patterns.

Q: Which part is called as heart of CRO ?

The heart of a CRO is the CRT, the cathode ray tube.In a cathode ray oscilloscope, the CRT produces the display: an electron gun generates and focuses a beam, deflection plates move it horizontally and vertically according to the time base and the input signal, and the beam strikes a phosphor screen to draw the waveform. All other sections exist to drive the CRT.The sweep (time base) generator provides the horizontal deflection voltage, the trigger circuit synchronises the sweep with the signal, and the vertical amplifier scales the input signal for the deflection plates. Each is essential, but they serve the CRT.

81.

If rise time of input amplifier is 10 nsec and the observed rise time on CRO is 15 nsec, then the appropriate rise time of the signal is ________.

A.10 nsec
B.11.18 nsec
C.15 nsec
D.18.02 nsec

Exam Year(s)

RSMSSB JE - 2025, RSMSSB - 2025,

Answer: B

The rise time of the signal is about 11.18 nsec.

When a signal passes through an amplifier, their rise times combine as the square root of the sum of squares: \(t_{obs}^{2} = t_{sig}^{2} + t_{amp}^{2}\).

\[ \begin{aligned} t_{sig} &= \sqrt{15^{2} - 10^{2}} \\ &= \sqrt{125} = 11.18\ \text{nsec} \end{aligned} \]

18.02 nsec adds the squares instead of subtracting them, 15 nsec ignores the amplifier, and 10 nsec is the amplifier's own rise time.

Discuss in Forum

82.

Match List I with List II and select the correct answer using codes given below :

List I	List II
(a) Electron microscope	(i) Electron gun
(b) Oscilloscope	(ii) Condensing magnetic lens
(c) Galvanometric recorder	(iii) Recording head
(d) Magnetic recorder	(iv) Drive motor

A.a-ii, b-iv, c-i, d-iii
B.a-ii, b-iii, c-i, d-iv
C.a-iii, b-ii, c-iv, d-i
D.a-ii, b-i, c-iv, d-iii

Exam Year(s)

MH SET - 2018, SET Exam - 2018,

Answer: D

The correct matching is a-ii, b-i, c-iv, d-iii.

An electron microscope focuses its beam with a condensing magnetic lens (ii).
An oscilloscope (cathode ray tube) produces its beam with an electron gun (i).
A galvanometric strip-chart recorder uses a drive motor to move the chart paper at a fixed speed (iv).
A magnetic recorder writes and reads the tape through a recording head (iii).

Both instruments in the first two rows have an electron gun and focusing, so the pairing turns on the part each is best known for: the electron microscope's distinctive element is its magnetic lens system. The codes giving the oscilloscope a recording head or a drive motor do not fit.

Discuss in Forum

83.

DSO cannot be used for :

A.Signal analysis
B.Signal monitoring
C.Signal digitisation
D.Signal generation

Exam Year(s)

MH SET - 2019, SET Exam - 2019,

Answer: D

A DSO cannot be used for signal generation.

A digital storage oscilloscope samples an input signal, digitises it with an ADC and stores the samples in memory, so it can display, monitor, store and analyse the signal, including measurements and FFT spectra.

It is a measuring instrument with inputs only; it does not generate signals. Signals are produced by function generators, signal generators or arbitrary waveform generators. Signal analysis, monitoring and digitisation are all things a DSO does.

Discuss in Forum

84.

A spectrum analyser is an instrument used for :

A.Visualising time variation of a waveform
B.Identifying dominant frequencies and harmonics
C.Introducing noise floor
D.Determination of impedance of an element

Exam Year(s)

MH SET - 2020, SET Exam - 2020,

Answer: B

A spectrum analyser is used for identifying dominant frequencies and harmonics.

A spectrum analyser displays signal amplitude against frequency, so it shows the frequency components of a signal: the fundamental, its harmonics, spurious signals and the noise floor.

Visualising the time variation of a waveform is the job of an oscilloscope. A spectrum analyser displays the noise floor but does not introduce it. Impedance is measured with an impedance analyser or LCR meter.

Discuss in Forum

85.

Lissajous figure corresponding to phase difference of 3π/4 is :

Exam Year(s)

MH SET - 2020, SET Exam - 2020,

Answer: D

The Lissajous figure for a phase difference of 3π/4 is (D), an ellipse tilted to fall to the right.

With equal frequencies and amplitudes on both axes, the pattern is a straight line rising to the right at zero phase difference, an ellipse rising to the right between 0 and π/2, a circle at π/2, and an ellipse falling to the right between π/2 and π, closing to a falling straight line at π.

3π/4 (135°) lies between π/2 and π, so the ellipse leans the other way, as in figure (D). Figure (A), a rising line, is 0 phase difference; figure (B), a circle, is π/2; figure (C), an ellipse rising to the right, is π/4.

Discuss in Forum

86.

Which of the following can store, manipulate and retrieve waveform related information ?

A.CRO
B.DMM
C.Spectrum analyser
D.DSO

Exam Year(s)

MH SET - 2023, SET Exam - 2023,

Answer: D

The instrument is the DSO, the digital storage oscilloscope.

A DSO samples the input with an analog-to-digital converter and stores the samples in memory. The stored waveform can then be displayed, measured, processed (zoomed, averaged, transformed) and recalled or transferred to a computer later, even for a single event that does not repeat.

An analog CRO displays the waveform only while it is present and cannot store it. A DMM measures single values such as voltage and current, not waveforms. A spectrum analyser displays the frequency content of a signal rather than storing the waveform itself.

Discuss in Forum

87.

The sweep generator of a CRO is used to produce :

A.sinusoidal voltage for the horizontal deflection of electron beam
B.sawtooth voltage for the vertical deflection of electron beam
C.sinusoidal voltage for the vertical deflection of electron beam
D.sawtooth voltage for the horizontal deflection of electron beam

Exam Year(s)

MH SET - 2024, SET Exam - 2024,

Answer: D

The sweep generator produces a sawtooth voltage for the horizontal deflection of the electron beam.

The time base must move the spot across the screen from left to right at a constant speed, so that horizontal distance represents time, and then return it quickly to the left to start again. A sawtooth does exactly this: a linear ramp for the trace and a fast drop for the retrace. It is applied to the horizontal (X) deflection plates.

The vertical plates receive the signal under observation, from the vertical amplifier, not the sweep. A sinusoidal sweep would move the spot at a varying speed and distort the time scale, so it is used only in special cases such as Lissajous patterns.

Discuss in Forum

88.

Which part is called as heart of CRO ?

A.CRT
B.Sweep generator
C.Trigger circuit
D.Amplifier

Exam Year(s)

MH SET - 2025, SET Exam - 2025,

Answer: A

The heart of a CRO is the CRT, the cathode ray tube.

In a cathode ray oscilloscope, the CRT produces the display: an electron gun generates and focuses a beam, deflection plates move it horizontally and vertically according to the time base and the input signal, and the beam strikes a phosphor screen to draw the waveform. All other sections exist to drive the CRT.

The sweep (time base) generator provides the horizontal deflection voltage, the trigger circuit synchronises the sweep with the signal, and the vertical amplifier scales the input signal for the deflection plates. Each is essential, but they serve the CRT.

Discuss in Forum

Loading…

Topics

Other Subjects

Tags: Cathode Ray Oscilloscope Questions and Answers || Cathode Ray Oscilloscope MCQ Questions and Answers || Cathode Ray Oscilloscope GK Questions and Answers || Cathode Ray Oscilloscope GK MCQ Questions || Cathode Ray Oscilloscope Multiple Choice Questions and Answers || Cathode Ray Oscilloscope GK || GK on Cathode Ray Oscilloscope || Electrical Measurements Questions and Answers || Electrical Measurements MCQ Questions and Answers || Electrical Measurements GK Questions and Answers || GK on Electrical Measurements

Cathode Ray Oscilloscope Questions and Answers

Topics

Other Subjects

About Us

Stay informed about all important Dates & Notifications